|
|
Post by chris on Aug 24, 2011 9:38:34 GMT -6
Sawcutting began on Sunday to remove and replace the existing patches between turn one and 2. Four sections totaling 37 cubic yards were removed and will be re poured on Wednesday and Thursday of this week. This will re open the passing lane between 1 and 2 and help rocket cars through the turn two apex.
The full road course will be closed this week, but the intermediate circuit will be available to members. The first scheduled full day will be Sunday for the motorcycles. Pics and the full story will be sent out through e mail.
|
|
|
|
Post by turbot on Aug 24, 2011 13:12:26 GMT -6
Sawcutting began on Sunday to remove and replace the existing patches between turn one and 2. Four sections totaling 37 cubic yards were removed and will be re poured on Wednesday and Thursday of this week. This will re open the passing lane between 1 and 2 and help rocket cars through the turn two apex. The full road course will be closed this week, but the intermediate circuit will be available to members. The first scheduled full day will be Sunday for the motorcycles. Pics and the full story will be sent out through e mail. That sounds killer, maybe Eon'll go down for a few minutes with his camera. Hey, if this makes the track faster, are y'all considering adjusting the breakout times..? T |
|
|
|
Post by Flying Tiger on Aug 24, 2011 19:50:10 GMT -6
I asked to come tracking on Tuesday and they told me to come on, so it should be ready to go before then!
|
|
|
|
Post by Ben - SM03 on Aug 25, 2011 8:29:34 GMT -6
What’s up Reggie, a little secret testing? You must really be worried.
|
|
|
|
Post by chris on Aug 25, 2011 8:47:37 GMT -6
Reggies secret testing, I can't comment, however, I can tell you I was at the track yesterday and the repairs are coming along nicely. The first two sections have been placed and finished. I spoke with our foreman this morning and last nights rain may delay thema bit but he feels confident they will get the remainder completed today. We just need to be patient, let the bikes run on Sunday and all call Reggie on his cell Tuesday around lunch to see howwe did. Confidence is high!!!!
Chris
|
|
|
|
Post by Flying Tiger on Aug 25, 2011 9:54:26 GMT -6
What’s up Reggie, a little secret testing? You must really be worried. The competition is enough to worry everyone! Plus, I have a SECRET weapon [which might be loaded with blanks...  ]. I just added this tidbit for Keith's benefit! LOL |
|
|
|
Post by chris on Aug 29, 2011 7:08:06 GMT -6
Tarps were puilled off Saturday moring and the form materials were removed yesterday morning. The bikes got to run on it and were very complimentary. There was still a little dust coming up when they ran over it, but when we get some rubber in it, we'll be just fine. The T-1 through T3 zone is back and better than ever. Looking forward to Reggies review.
Chris
|
|
|
|
Post by Flying Tiger on Aug 30, 2011 17:38:27 GMT -6
I tested the track today and it is nicely done IMHO. The patches are really White and easy to spot, but they are smooth to cross over. No problems with the patches. Good job, guys. See you there Friday and Saturday. Did I mention it was HOT?!
|
|
|
|
Post by ccsintlcircuits on Jun 27, 2012 6:06:16 GMT -6
The printed circuit board fabrication is a part of electronic. There are a lot of electronics device which makes you and your house safe like printed circuit board fabrication. PCB used for the safety purpose.
|
|
|
|
Post by ccsintlcircuits on Jun 29, 2012 3:41:25 GMT -6
printed circuit board fabrication is used for satisfy a customer needs and fullifill a requirement .and it manufactured a electronic circuit board.and it provide a better quality product .
|
|
]. I just added this tidbit for Keith's benefit! LOL